In: Models

    Earrings & jewelry 3D print models

    (16)

    Jewellers adopted resin printing before hobbyists did, and small wearable pieces remain one of the best uses of an MSLA printer. The 3D printed jewellery here covers earrings, pendants, rings and bracelets: snowflake and Christmas tree earrings, a wolf pendant, a Medusa head pendant, signet rings, plus a few holders and boxes to keep them in.

    Jewellery prints are small, fast and cheap in resin, but they ask for care at two points. Thin loops and earring hooks need a tough or flexible resin rather than a brittle standard one, and tiny parts need an orientation where supports touch the back face only.

    Several of these pieces take standard findings, jump rings, ear hooks and chains from any craft shop; the model page gives the hole diameter and the creator's recommended resin. For wearable pieces of another kind, the keychains theme uses the same materials and the same loop rules.

    16 models

    Goderick, Guardian of the Ring - 3D printable Fantasy
    Goderick, Guardian of the Ring
    ‌
    ‌
    Abaddon's Signet Ring - 3D printable Characters
    Abaddon's Signet Ring
    ‌
    ‌
    Pendant Head of Medusa - 3D printable Wall Decorations
    Pendant Head of Medusa
    ‌
    ‌
    Hell's Chain Bracelet - 3D printable Props
    Hell's Chain Bracelet
    ‌
    ‌
    Wolf Pendant - 3D printable Props
    Wolf Pendant
    ‌
    ‌
    Jeweled Scrabaeus - 3D printable Creatures
    Jeweled Scrabaeus
    ‌
    ‌
    Christmas Tree earrings/ornament - 3D printable Props
    Christmas Tree earrings/ornament
    ‌
    ‌
    Flower earrings - 3D printable Others
    Flower earrings
    ‌
    ‌
    Unicycle Earrings - 3D printable Props
    Unicycle Earrings
    ‌
    ‌
    Sunflower earrings - 3D printable Others
    Sunflower earrings
    ‌
    ‌
    Snowflake earrings - 3D printable Props
    Snowflake earrings
    ‌
    ‌
    Celine's Sharktooth Necklace - 3D printable Characters
    Celine's Sharktooth Necklace
    ‌
    ‌
    Cute Heart Jewelry Box - 3D printable Organizer
    Cute Heart Jewelry Box
    ‌
    ‌
    Edelweiss Earrings/Accessories - 3D printable Others
    Edelweiss Earrings/Accessories
    ‌
    ‌
    Easter Egg Earrings - 3D printable Others
    Easter Egg Earrings
    ‌
    ‌
    Cone ring holder - 3D printable Organizer
    Cone ring holder
    ‌
    ‌

    Frequently asked questions

    A tough, ABS-like or flexible resin. Standard resins are brittle and snap at thin loops and hooks. For pieces that touch skin, finish them with a full cure and a clear coat, or use a resin the manufacturer rates as skin-safe.

    Print at 0.025 to 0.035 mm layers, tilt the piece 20 to 30 degrees, and keep supports on the back or inside of the design. Lychee Slicer's light supports with small tips leave almost no mark on jewellery-size parts.

    Yes, with a castable resin designed to burn out cleanly in a kiln. Standard resin leaves ash. The ring files here are geometry only; whether a design suits casting depends on its wall thickness, so ask the creator or check the model notes.

    Models in the Lychee Library open directly in Lychee Slicer, with the supports and settings prepared by the creator. Whether the file can also be exported depends on the licence each creator sets, shown on the model page.